wdh-site
wdh-site
kinglift kinglift

Product Categories

kinglift

Electric Reach Forklift Series - KLR

Electric reach forklift

 

 

 

China electric reach forklift

 

 

Applicable for single-faced and double-faced pallets   

Inquiry now
China electric reach forklift

    China electric reach forklift - Kinlift Forklifts electric reach forklift

  • 01

    Load Capacity Chart

     

    Lift Height(mm) Load Center at 500 mm
    Load Center at 600 mm
    KLR10/B   KLR15A/B KLR20A/B KLR10/B KLR15A/B KLR20A/B
    5000 1500 2000 2500 1300 1800 2300
    5500 1300 1800 2300 1100 1600 2100
    6000 1100 1600 2100 900 1400 1900
    6500 900 1400 1900 700 1200 1700
    7000   1200 1700   1000 1500
    7500   1000 1500   800 1300
    8000     1300     1100
    8500     1100     900

     

  • 02

    Operation precautions:

    Operation precautions of China electric reach forklift:

     

    (1) When using the China electric reach forklift, pay special attention to timely charging and correct maintenance of the battery. Pay attention to the method when charging the battery, not only make the battery fully charged, but also not cause the battery to overcharge.

     

    (2) In the electric reach forklift operation, try to minimize the use of long-term and long-distance acceleration. When the vehicle starts and the speed increases, stabilize the accelerator pedal. If the road condition is better, the vehicle will continue to accelerate. When the vehicle needs to decelerate, relax the accelerator pedal and lightly depress the brake pedal, so that the energy of deceleration can be fully utilized. If the vehicle has a regenerative braking function, the kinetic energy during deceleration can be recovered. When the vehicle is going down a slope, do not disconnect the circuit that drives the motor, and gently step on the brake pedal to make the vehicle run in a regenerative braking state, and use the kinetic energy of the vehicle down to reduce the energy consumption of the battery.

     

    (3) When the China electric reach forklift is in operation, do not mistake the "forward, reverse" direction switch as a steering switch. Unless you need to decelerate urgently, don't press the brake pedal to the end. During the operation of the electric reach forklift, when the battery power is found to be insufficient (which can be obtained from the electricity meter, the power loss indicator and other alarm devices), the battery should be charged as soon as possible to prevent the battery from over-discharging.

  • 03

    Working principle:

    The working principle of China electric reach forklift:

     

    The mast or fork frame of the China electric reach forklift can move forwards and backwards. The mast forward-moving forklift means that the mast drives the fork to move forward during operation, and extends out of the front wheel to fork or put down the goods. When the fork is walking, With the cargo retracted, the center of gravity of the cargo is within the supporting surface; and the forward-moving forklift truck means that the shelf drives the fork to move forward beyond the front wheel for operation, and when walking, the fork frame drives the fork to retract into the supporting plane.

     

    The China electric reach forklift has two extended outriggers. The outriggers are higher. There are two wheels at the front of the outriggers. The function of the outriggers is to ensure the stability of the forklift under load. Compared with the forklift with legs, the front wheels are larger and the outriggers are higher. During operation, the outriggers cannot be inserted into the bottom of the goods, and the mast can move along the track inside the outriggers with the entire lifting mechanism, so that the fork forks After picking up the goods, it can be retracted by slightly raising it to a height to ensure the stability of the forklift during operation.

     

    The mast of the electric reach forklift can be moved forward along the inner track of the outrigger to facilitate forklifting of goods. After fork picking up the goods, the mast is raised to a certain height, and the mast can return to its original position along the inner track of the outriggers, so that the center of gravity of the goods is in the front and rear supporting legs of the vehicle, so the stability is very good. Suitable for operations in workshops and warehouses.

     

    The mast of the electric reach forklift can be moved forward along the inner track of the leg with the lifting mechanism, which is convenient for fork and pick up the goods. After picking up the cargo, the mast returns to its original position along the inner track of the outrigger after lifting a short height.

     

    Kinlift Forklifts is one of the leading China Electric forklift manufacturers that focuses on counterbalance pallet stacker. Innovation is the driving force for us to establish competitive advantage, and is the key to our leading position in the fierce international market competition.

     

    For more information on 3000kg Electric Balanced Straddlestacker, click here.

    For more information on 3T Electric Walkiestacker, click here.

    For more information on lithiumbattery Electric Forklift Trucks, click here.

    For more information on 2.5T Battery Forklift industrialequipment, click here.

     

    If you want to know more about YOUTUBE, you can click on the relevant link below.

     

    https://www.youtube.com/channel/UC0LbTKF6n0Y_foDLWhAl0aA/featured

Hot Products
tsingone

Electric Reach Forklifts with Rider Platform - KLR-E/D

Place of Origin:Jiangsu, China
View More
tsingone

Electric Reach Forklifts with Rider Platform - KLR-E/D

Place of Origin:Jiangsu, China
View More
wdh-site
wdh-site

We look forward to your contact.

Contact us
Products
Our advantage
News
FOLLOW US
Jiangsu Kinlift equipment.,Ltd. Support By Hangzhou Great Master